Quadra-Fire EDGE 60 Manuel du propriétaire télécharger pdf (Page 10)

Page 10

7051-158B

December 6, 2011

EDGE 60 Pellet Fireplace

G. Filling the Hopper with Fuel

NOTICE: RAISED PLATFORM INSTALLATIONS

Consideration must be given for ﬁ lling the hopper with fuel

when determining the height of the raised platform. It must

not be so high that it interferes with the safety of ﬁ lling the

hopper with fuel.

1. Start-Up Cycle

During this cycle:

• Igniter turns on for 90 seconds to heat up the air in the

ﬁ repot

• Combustion blower starts

• Vacuum switch comes on

• Feed motor turns on adding fuel to the ﬁ repot and the

appliance waits for the ﬁ re to start

The duration of start-up depends on the type and quality

of fuel used. It is normal to see some smoke during the

ignition process as moisture evaporates and the fuel lights.

The smoke will stop once the ﬁ re starts.

H. Starting Your First Fire

1. Fuel Selection

To start your ﬁ rst ﬁ re, you must:

• Select the appropriate fuel on the FUEL SELECTION screen

on the thermostat wall control to match the fuel you have

chosen to burn.

• If the proper fuel is not selected your appliance will not

operate properly.

• For example, if you have selected wood pellets and you are

burning corn, the appliance may not light, it may go out or

overfeed. Figure 10.1.

NOTE: If you are lighting your appliance for the ﬁ rst time:

• The feed tube will be empty and it can take some time to ﬁ ll

it with fuel before you will see a ﬁ re

• Put a handful of fuel in the ﬁ repot (priming) to speed up the

process. You can also do this when you have run com-

pletely out of fuel.

Sunflower Seeds

Corn

Utility Pellet

Softwood Pellet

Wheat

Hardwood Pellet

DONE

SELECT

FUEL SELECTION

I. Ignition Cycles

The ﬁ replace engine is controlled by the digital thermostat

wall control. The digital display on the wall control will tell

you what your appliance is doing in the upper left corner

(System Status). Figure 10.3.

READY

Set at: 73

12:30 PM

HEAT OUTPUT

System Status

Every time the thermostat calls for heat, the appliance steps

through ﬁ ve cycles:

1 Start-Up Cycle 4 Shutdown Cycle

2 Soft-Start Cycle 5 Auto-Clean Cycle

3 Heating Cycle

The duration and characteristics of these cycles may be dif-

ferent with each type of fuel selected.

2. Comfort Level Selection

Once your fuel is selected, select the temperature at the desired

setting on the SET COMFORT LEVEL screen. Figure 10.2.

3. Automatic or Manual Setting

The automatic setting will control the heat output based on

the comfort level selection. The manual setting allows you to

manually control the heat output settings.

Figure 10.2

Figure 10.3

Figure 10.1

WARNING! RISK OF FIRE!

Do NOT operate appliance:

• With appliance door open

• With ﬁ repot ﬂ oor open

• With ash pan removed

• Without the two slide rail attachment bolts secured to

ﬁ replace

•

Check the hopper and make sure it is empty before ﬁ lling

with fuel.

• Open the front to expose the hopper door. Pull down on the

hopper door to open and ﬁ ll with fuel. The hopper door can

now serve as a shelf to support the bag of fuel

• Do not over ﬁ ll the hopper. The hopper door must be com-

pletely closed to maintain proper vacuum and for the feed

motor to operate. An error ICON will appear on the wall

control if the hopper door is not properly closed.

• Do not leave any part of the fuel bag on the appliance after

ﬁ lling hopper.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 57 58

Commentaires sur ces manuels

Pas de commentaire

Quadra-Fire EDGE 60 Manuel du propriétaire Page 10

Commentaires sur ces manuels

Produits connexes et manuels pour Poêles Quadra-Fire EDGE 60