Quadra-Fire EDGE 60 Manuel du propriétaire Page 52
- Page / 58
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Page 52
7051-158B
December 6, 2011
R
EDGE 60 Pellet Fireplace
With proper installation, operation, and maintenance your appli-
ance will provide years of trouble-free service. This trouble-
shooting guide shall be used by a qualifi ed service technician
only).
Error Message
Possible Cause Corrective Action
Bad wall control or control board
3 wires have loose connections or installed
wrong
Replace wall control or control board
Check connections
BAD TC DROP TUBE
(TC = Thermocouple)
Drop tube thermocouple is broken or leads are
reversed
Check connections
Replace thermocouple
BAD TC FIREPOT
(TC = Thermocouple)
Firepot thermocouple is broken or leads are
reversed
Check connections
Replace thermocouple
SNAP DISC TRIPPED Overheat sensor (snap disc) has tripped
Convection blower may need cleaning
Turn power off to appliance and manually
reset snap disc then turn power back on
Clean convection blower if needed
VACUUM SW ERROR
(SW = Switch)
Vacuum switch is bad
Vacuum hose is plugged/disconnected
Check connections. Bypass vacuum with
jumper wire, if runs, switch is bad. Replace
switch
Check vacuum hose
COMB BLOWER JAMMED Combustion blower is blocked/jammed Remove blockage
Replace blower if necessary
Turn the power switch OFF and then back
ON to clear the error
AUGER JAMMED Auger jammed, feed motor bad Pull the feed system and inspect
Clear jam and Press Retry
MISSED IGNITION Igniter bad or poor harness connection
Out of fuel or fuel is bridging in hopper
Faulty fi repot thermocouple connection has
shorted.
Check connections, if OK replace igniter
Break up bridging pellets. Refi ll hopper
Replace the thermocouple
Press Retry
MIN FIREPOT TEMP Out of fuel Refi ll hopper
Add handful of pellets to fi repot to prime it
Press Retry
MAX DROP TUBE TEMP Stove in over-heat condition
Flame height set too high
Components may need cleaning
Confi rm setting matches burning fuel
Adjust fl ame height
Clean the fi rebox, heat exchanger, convec-
tion blower, fi repot and ash pan
CONV BLOWER JAMMED Convection blower blocked/jammed Remove blockage
Replace blower if necessary
Turn the power switch OFF and then back
ON to clear the error
CHECK ASHPAN Auto-clean jammed
Auto-clean switch is bad
Linkage has become disconnected
If ashpan is empty, check for a jam. Use a
screw driver and fi rmly push in the fi repot
fl oor holes and fl ex spring and push toward
home to release jam
Replace switch
Reconnect linkage
SCREEN GOES BLANK Static discharge or nearby lightning or
Electric fast transients at the input mains
Power switch in OFF position
Wait 25 seconds and press any key to
refresh the screen.
Turn to ON position
Hopper lid not closed all the way
Switch is out of adjustment (auger will not
function)
Close the lid. If that didn’t work replace the
switch
Adjust or replace switch
Firebox door is not latched properly
Fireplace not rolled in completely
Slide rail bolts not installed
Adjust or replace door switch
Replace interlock switch or magnet
Install bolts
Out of fuel Check fuel level, if OK the switch may be
out, replace switch
12
Troubleshooting For Installers
- EDGE™ 60 1
- ATTENTION: 2
- User’s Guide 3
- TABLE OF CONTENTS 3
- Listing and Code Approvals 6
- by sifting 8
- (such as soybean oil) 8
- F. Before Your First Fire 9
- E. Power Switch 9
- EDGE 60 Pellet Fireplace 10
- H. Starting Your First Fire 10
- I. Ignition Cycles 10
- (Feed Rate) Adjustment 12
- L. Clear Space 13
- A. Proper Shutdown Procedure 14
- Troubleshooting for Homeowner 21
- B. Wall Control Error Codes 22
- Error Message 22
- Installer’s Guide 23
- C. Tools And Supplies Needed 24
- Crush Hazard! 25
- WARNING 25
- A. Recommended Locations 26
- B. Hearth Extension 26
- D. Frame the Fireplace 27
- Envelope 27
- E. Construct the Chase 28
- F. Finishing Material 29
- Tuscan and Natural Fronts 30
- Opening Clearances 31
- (1:1 rise to run ratio) 32
- I. Non-Combustible Materials 33
- J. Combustible Materials 33
- Installation of Fireplace 34
- B. Avoiding Smoke and Odors 39
- Negative pressure can 40
- C. Negative Pressure 40
- D. Draft 40
- F. Equivalent Feet of Pipe 41
- G. Pipe Selection Chart 42
- Left Rear Corner 43
- Right Rear Corner 43
- Rear of Fireplace 43
- Install Outside Air Kit 44
- Non-combustible 46
- Hearth Extension 46
- 0 in. (0mm) to Standoff 46
- Mobile Home Installation 47
- Appliance Set-Up 48
- Hinge on Fireplace 49
- Hinge on Front 49
- Start with Bottom Hinge 49
- Alignment and then Top 49
- Hinges Aligned 49
- Remove 4 screws 50
- Glass with Gasket 50
- Metal Bracket 50
- Page 52 52
- 7051-158B 52
- December 6, 2011 52
- 4-7/8 in 53
- Reference Materials 53
- B. Component Functions 54
- Control Board Schematic 55
- Slide Rails 56
Produits connexes et manuels pour Poêles Quadra-Fire EDGE 60
(52 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.743 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels