Quadra-Fire EDGE 60 Manuel du propriétaire télécharger pdf (Page 55)

December 6, 2011

7051-158B

Page 55

EDGE 60 Pellet Fireplace

Figure 54.1 - Power Supply Figure 54.2 - Control Board

120V AC in

120V AC out to

Control Board

15V DC out to

Control Board

Fuse 15A 250V

(need to remove

cover)

Heat sinks are taped to cover for

shipping. Slowly lift cover and cut the

tape holding them in place and then

you can remove the cover.

# Description # Description # Description

1 Combustion Blower 7 Thermostat Wall Control 12 Igniter

2 Auto-Clean System 8 Combustion Blower (feedback) 13 AC Power In for Igniter

3 Feed/Auger Motors 9 Firepot Thermocouple 14 Convection Blower Power

4 Hopper/Door Switches 10 Drop Tube Thermocouple 15 Overheat Sensor (Snap Disc)

5 Auger/Auto Clean/Vacuum Switches n/a Not Used 16 DC Power In from Power Supply

6 Low Fuel 11 Convection Blower (feedback) 17 12 Volt Battery Back-up

10111213

15 16

n/a

Fuse 15A 120V,

under the cover

Fuse 15A 120V,

under the cover

18.

Overheat Sensor (Snap Disc)

Location: Mounted on the back of the drop tube in the center

of the appliance and has a reset button. Remove the right side

panel to access.

Function: If the ﬁ re tries to burn back into the feed system or

push exhaust up the feed tube, this sensor will shut the appli-

ance down, however the wall control will still display messages.

This sensor must be manually re-set. Disconnect power before

resetting.

19. Thermocouple - Firepot

Location: On top of the ﬁ repot inside the thermocouple cover

(ceramic protection tube)

Function: Sends a millivolt signal to the control board telling the

control board there is a ﬁ re in the ﬁ repot.

20. Thermocouple - Drop Tube

Location: Bottom of the drop tube on the right side and

attached with a wing nut

Function: Turns the convection blower on and off, varies

the speed of the convection blower and will shut down

appliance if internal heat exceeds set temperature.

21. Vacuum Switch

Location: Right side of the appliance under the feed

motor behind right side panel and connects to the drop

tube with a hose

Function: Turns the feed system on when vacuum is

present in the ﬁ rebox. The vacuum switch is a safety

device to shut off the feed motor if the exhaust or the

heat exchanger system is dirty, plugged or if the ﬁ rebox

door is open.

22. Wall Control, Thermostat

Location: Interior wall of the home

Function: The appliance is designed to run on a custom

designed 3.3 volt DC thermostat wall control. It will not

operate on any other wall control. Refer to the instruc-

tions supplied with the appliance, located in the compo-

nent pack.

23. Wiring Schematic for Power Supply

See Figure 54.1 below.

24. Wiring Schematic for Control Board

See Figure 54.2 below.

Control Board Schematic

16. Power Supply

Location: At the rear of the appliance

Function: Converts 120 volt AC current to 15 volt DC current to

power the appliance.

17. Power Switch

Location: Lower front right side of appliance

Function: Turns the power on and off to the appliance

1 2 ... 50 51 52 53 54 55 56 57 58

Commentaires sur ces manuels

Pas de commentaire

Quadra-Fire EDGE 60 Manuel du propriétaire Page 55

Commentaires sur ces manuels

Produits connexes et manuels pour Poêles Quadra-Fire EDGE 60